Click for PDF
Technical Data Sheet
Eastar™ Polyester MN052


Applications
  • Blood contact and dialysis
  • Fluid administration
  • Medical devices
  • Medical supplies
Key Attributes
  • Chemical resistance to most medical solvents including lipids and IPA
  • Gamma and E-beam color stability

Product Description
Eastar™ Polyester MN052 has been tested for FDA/ISO 10993 and USP Class VI Biological Evaluation testing after Gamma and EtO sterilization. Eastar™ Polyester MN052 does not contain a mold release. It has a relatively high flex modulus and yield strength. This product has high flow characteristics.

This product has been GREENGUARD INDOOR AIR QUALITY CERTIFIED
The GREENGUARD INDOOR AIR QUALITY CERTIFIED Mark is a registered certification mark used under license through the GREENGUARD Environmental Institute (GEI). GEI is an industry-independent, non-profit organization that oversees the GREENGUARD Certification Program. The GREENGUARD Certification Program is an industry independent, third-party testing program for low-emitting products and materials for indoor environments. For more information about GEI and to obtain printable certificates for Eastman™ Copolyesters, visit greenguard.org. Choose Eastman Chemical Company under the Manufacturer category and click search to display a list of our products.



Typical Properties

PropertyaTest MethodbTypical Value, Unitsc
Injection Molded Properties
Specific GravityD 7921.32
Water Absorption, 24 h immersionD 5700.1 %
Mold Shrinkage 
     Parallel to Flow, 3.2-mm (0.125-in.) thicknessD 9550.004 mm/mm (0.004 in./in.)
Tensile Stress @ YieldD 63857 MPa (8300 psi)
Tensile Stress @ BreakD 63826 MPa (3800 psi)
Elongation @ YieldD 6384 %
Flexural ModulusD 7902500 MPa (3.6 x 105 psi)
Flexural Yield StrengthD 79081 MPa (11700 psi)
Rockwell Hardness, R ScaleD 785110
Izod Impact Strength, Notched 
     @ 23°C (73°F)D 25651 J/m (1.0 ft·lbf/in.)
     @ -40°C (-40°F)D 25636 J/m (0.7 ft·lbf/in.)
Impact Strength, Unnotched 
     @ 23°C (73°F)D 4812NB
     @ -40°C (-40°F)D 4812NB
Deflection Temperature 
     @ 0.455 MPa (66 psi)D 64866 °C (151 °F)
     @ 1.82 MPa (264 psi)D 64862 °C (144 °F)
Vicat Softening Temperature 
     @ 1 kg loadD 152579 °C (174 °F)
Dielectric Constant 
     1 kHzD 1503.2
     1 MHzD 1503.0
Dissipation Factor 
     1 kHzD 1500.008
     1 MHzD 1500.02
Arc ResistanceD 495155 sec
Volume ResistivityD 2571016 ohm·cm
Surface ResistivityD 2571016 ohms/square
Dielectric Strength, Short Time, 500 V/sec rate-of-riseD 14915.7 kV/mm (400 V/mil)
Typical Processing Conditions
Drying Temperature 150-160 °C (300-320 °F)
Drying Time 4-6 hrs
Processing Melt Temperature 275-295 °C (530-565 °F)
Mold Temperature 10-30 °C (50-90 °F)

aUnless noted otherwise, all tests are run at 23°C (73°F) and 50% relative humidity.
bUnless noted otherwise, the test method is ASTM.
cUnits are in SI or US customary units.


Eastman Medical Disclaimer
It is the responsibility of the medical device manufacturer ("Manufacturer") to determine the suitability of all component parts and raw materials, including any Eastman product, used in its final product in order to ensure safety and compliance with requirements of the United States Food and Drug Administration (FDA) or other international regulatory agencies.

Eastman Chemical Company products have not been designed for nor are they promoted for end uses that would be categorized by either the United States FDA or by the International Standards Organization (ISO) as implant devices. Eastman products are not intended for use in the following applications: (1) in any bodily implant applications for greater than 30 days, based on FDA-Modified ISO-10993, Part 1 “Biological Evaluation of Medical Devices” tests (including any cosmetic, reconstructive or reproductive implant applications); (2) in any cardiac prosthetic device application, regardless of the length of time involved, including, without limitation, pacemaker leads and devices, artificial hearts, heart valves, intra-aortic balloons and control systems, and ventricular bypass assisted devices, or (3) as any critical component in any medical device that supports or sustains human life.

Eastman Chemical Company products offered for the medical market have met selected FDA-Modified ISO-10993, Part 1 “Biological Evaluation of Medical Devices” tests with human tissue contact time of 30 days or less. The tests include: cytotoxicity, sensitization, irritation or intracutaneous reactivity, systemic toxicity (acute), subchronic toxicity (sub-acute), implantation, hemocompatibility. The Manufacturer is responsible for the biological evaluation of the finished medical device.

The suitability of an Eastman Product in a given end-use environment is dependent upon various conditions including, without limitation, chemical compatibility, temperature, part design, sterilization method, residual stresses, and external loads. It is the responsibility of the Manufacturer to evaluate its final product under actual end-use requirements and to adequately advise and warn purchasers and users thereof.

Comments
Properties reported here are typical of average lots. Eastman makes no representation that the material in any particular shipment will conform exactly to the values given.


Eastman and its marketing affiliates shall not be responsible for the use of this information, or of any product, method, or apparatus mentioned, and you must make your own determination of its suitability and completeness for your own use, for the protection of the environment, and for the health and safety of your employees and purchasers of your products. No warranty is made of the merchantability of fitness of any product, and nothing herein waives any of the Seller's conditions of sale.


7/15/2021 9:46:03 AM