Click for PDF View TDS
Technical Data Sheet
Piccotac™ 9095-E Hydrocarbon Resin


Applications
  • Adhesives/sealants-B&C
  • Carpet construction
  • Case and carton closures
  • Casting wax
  • Hygiene adhesives
  • Labels non food contact
  • Packaging tape
  • Polymer modification
  • Protective coatings
  • Road markings
  • Roofing ingredients
  • Solvent borne packaging adhesives
  • Specialty tape
  • Tape non food contact
  • Wire/cable
Key Attributes
  • Aliphatic resin with a low level of aromatic-modification
  • Excellent adhesion to styrene-isoprene-styrene (SIS) block copolymers
  • Excellent balance of peel and shear
  • Excellent compatibility with EVA, APO and metallocene polymers for packaging adhesives
  • Excellent peel and tack properties
  • Light color, low odor

Product Description
Piccotac™ 9095-E hydrocarbon resin is a low molecular weight, slightly aromatic-modified aliphatic C5 tackifier designed for the adhesives industry. This light colored resin is compatible with styrenic block copolymers, EVA, and many polar elastomers.







It is widely used with other tackifier resins, such as rosin esters and C9 hydrocarbon tackifiers to improve performance. It is primarily used in hot melt adhesives and pressure sensitive adhesives. Piccotac™ 9095-E is stabilized by the addition of antioxidant.


Typical Properties

PropertyaTest MethodbTypical Value, Unitsc
Ring and Ball Softening PointASTM E 2895 °C
Color, GardnerdASTM D61663
Cloudpoint, MMAPe 86 °C
Molecular Weightf 
     Mn 990
     Mw 1900
     Mw/Mn 1.9
     Mz 3690

aUnless noted otherwise, all tests are run at 23°C (73°F) and 50% relative humidity.
bUnless noted otherwise, the test method is ASTM.
cUnits are in SI or US customary units.
d50% solids in toluene.
eCloud point temperature from 2:1 Vol:Vol aniline-methylcyclohexane, Eastman method.
fMolecular weight measured via Gel Permeation Chromatography (GPC) using polystyrene standards, elution with THF.



Compatibility and Solubility
Compatible at all ratios or in limited but practically useful proportions, with natural and synthetic rubbers, low-vinyl acetate EVA (ethylene-vinyl acetate) copolymers, EnBA (ethylene n-butyl acetate) copolymers, APAO (amorphous poly-alpha-olefins), SIS (styrene-isoprene-styrene) block copolymers, SIBS (styrene-isoprene/butadiene-styrene) block copolymers, SEBS (styrene-ethylene/butylene-styrene) block copolymers, SEPS (styrene-ethylene/propylene-styrene) block copolymers, polyethylene polymers, polypropylene polymers, paraffin and microcrystalline waxes, PIB (polyisobutene), OBC (olefinic block copolymers), mPE (metallocene-catalyzed polyethylene), mPP (metallocene-catalyzed polypropylene), and TPE (thermoplastic elastomers).
Soluble at all useful proportions in aliphatic, aromatic, and chlorinated hydrocarbons, esters and ethers, and t-butyl acetate. Insoluble in alcohols, glycols and water.


Packaging
Piccotac™ 9095-E Hydrocarbon Resin is pastillated and packed in polyethylene bags of 20 kg net, and supplied on shrink-wrapped pallets of 50 bags (1000 kg) each, from Eastman facilities in the Netherlands and from warehouses located in Europe.

Storage
Flaked and pastillated forms of resins may fuse, block or lump under any of the following conditions: (1) in hot weather climates (2) if stored near steam pipes or other sources of heat and (3) upon prolonged storage. Storage at temperatures above 30°C should be avoided. Inside storage in a temperature-controlled area is necessary in order to prevent problems, such as lumping. Due to the nature of the product, claims regarding lumping cannot be accepted.

Resins are prone to gradual oxidation, some more so than others. This could result in darkening and/or it could have an adverse effect on the solubility of the resin in organic solvents or on its compatibility with polymers. Accordingly, it is recommended that strict control of inventory be observed at all times, taking care that the oldest material is used first.

Piccotac™ 9095-E Hydrocarbon Resin material will remain within product specification limits for a period of at least twelve months after shipment from Eastman production facilities in The Netherlands, provided storage conditions outlined in this data sheet are observed. However, as we can neither anticipate the conditions under which the resin is processed nor the end use applications for which it is used, we recommend that the material be tested upon receipt.



Comments
Properties reported here are typical of average lots. Eastman makes no representation that the material in any particular shipment will conform exactly to the values given.


Eastman and its marketing affiliates shall not be responsible for the use of this information, or of any product, method, or apparatus mentioned, and you must make your own determination of its suitability and completeness for your own use, for the protection of the environment, and for the health and safety of your employees and purchasers of your products. No warranty is made of the merchantability of fitness of any product, and nothing herein waives any of the Seller's conditions of sale.


5/21/2020 2:40:48 PM