Click for PDF View TDS
Technical Data Sheet
Eastman Tritan™ Copolyester MX810


Applications
  • Blood contact and dialysis
  • Blood tubes
  • Fluid administration
  • Medical devices
  • Medical equipment
  • Medical labware
Key Attributes
  • Excellent clarity
  • Excellent hydrolytic stability
  • Fast drying times
  • Good chemical resistance
  • Improved processability over traditional copolyesters
  • Outstanding impact resistance
  • Quick cycle times

Product Description
Eastman Tritan™ MX810 is an amorphous copolyester with excellent appearance and clarity. Its most outstanding features are excellent toughness, hydrolytic stability, and heat and chemical resistance. This new generation copolyester can also be molded into various applications without incorporating high levels of residual stress. Tritan MX810 has been tested for FDA/ISO 10993 and USP Class VI Biological Evaluation testing after Gamma and ETO sterilization.

Typical Properties

PropertyaTest MethodbTypical Value, Unitsc
General Properties
Specific GravityD 7921.17
Mold ShrinkageD 9550.005-0.007 mm/mm (0.005-0.007 in./in.)
Mechanical Properties
Tensile Stress @ YieldD 63844 MPa (6400 psi)
Tensile Stress @ BreakD 63853 MPa (7700 psi)
Elongation @ YieldD 6387 %
Elongation @ BreakD 638140 %
Tensile ModulusD 6381585 MPa (2.28 x 105 psi)
Flexural ModulusD 7901585 MPa (2.28 x 105 psi)
Flexural Yield StrengthD 79066 MPa (9600 psi)
Rockwell Hardness, R ScaleD 785115
Izod Impact Strength, Notched 
     @ 23°C (73°F)D 256650 J/m (12.2 ft·lbf/in.)
Impact Strength, Unnotched 
     @ 23°C (73°F)D 4812NB
Optical Properties
Total TransmittanceD 100392 %
HazeD 1003<1 %
Thermal Properties
Deflection Temperature 
     @ 0.455 MPa (66 psi)D 648109 °C (228 °F)
     @ 1.82 MPa (264 psi)D 64892 °C (198 °F)
Typical Processing Conditions
Drying Temperature 88 °C (190 °F)
Drying Time 4-6 hrs
Processing Melt Temperature 260-282 °C (500-540 °F)
Mold Temperature 38-66 °C (100-150 °F)

aUnless noted otherwise, all tests are run at 23°C (73°F) and 50% relative humidity.
bUnless noted otherwise, the test method is ASTM.
cUnits are in SI or US customary units.


Technical Disclaimer
Eastman makes no representation and disclaims any warranty that the material in any particular shipment will conform exactly to the values given. Values as well as the performance of the final molded article may be affected by various factors such as the part design, mold design or tooling, drying, processing conditions as well as coloring or pigmentation of the product. No warranty of merchantability or fitness for use is made, and nothing herein waives any of the Seller''s conditions of sale. You must make your own determination of the suitability of this product in your specific application due to the many factors (e.g. design, processing and conditions of use) that affect the performance of the final molded article. Suitability of use should be evaluated with appropriate testing and analysis. The processing melt temperature and mold temperature refer to the actual resin melt temperature and actual mold surface temperature respectively. Consider overall resin residence time, part shot size utilization and part geometry to set appropriate processing melt temperature and mold temperature in order to minimize IV loss and maximize molded part performance.

Comments
Properties reported here are based on limited testing. Eastman makes no representation that the material in any particular shipment will conform exactly to the values given.


Eastman and its marketing affiliates shall not be responsible for the use of this information, or of any product, method, or apparatus mentioned, and you must make your own determination of its suitability and completeness for your own use, for the protection of the environment, and for the health and safety of your employees and purchasers of your products. No warranty is made of the merchantability of fitness of any product, and nothing herein waives any of the Seller's conditions of sale.


9/12/2019 11:50:48 AM